Parametric EQ

BYOC Parametric EQ (equalizer) pedal. It's been stated that, "A graphic equalizer is a toy, but a parametric equalizer is a tool."

We don't necessarily agree with this statement, but we will agree that someone using a parametric equalizer requires a bit more sophistication in what they're looking for tone-wise, and a willingness to invest more time when it comes to using one. One of the benefits (some might say it's a drawback) of using a parametric equalizer is that it tends to demand that the person using it use their ears to get the sound they're looking for, instead of just allowing that person to "use settings they already know they like" - especially when they're using one for the first time.

• Thermionic Studios has one(1) BYOC Parametric EQ pedal available for rental.

Controls

Image from expired reverb.com auction

So usually we just launch into a description of the controls, but we need to do it a bit differently here since the controls require a bit more nuance in their description.

Each bank of controls has the same feature set:

• Frequency-band Width Control: Width or "Q"
• Selected Frequency-band Volume: Boost / Cut
• Frequency-band "Midpoint" Select: Freq. Select

These controls are incredibly interactive, and as described above, it takes a bit of contextual knowledge to understand what's going on. After the description of the control banks, we do expand on the nature of the tone controls and the parameters controlled further down in this article, including some diagrams that should help clarify the concepts.

Bass Bank

This bank modifies adjustments to bass frequencies from 33Hz up to 330Hz. Knobs are on left side and run up-and-down

• Knob 1 - "Width or Q": Controls the breadth of the bass frequencies to be modified.
• Knob 2 - "Boost / Cut": Adjusts the intensity of the bass frequencies with fully clockwise being maximum.
• Knob 3 - "Freq. Select": Selects where in the bass (33Hz up to 330Hz) that the other bass tone controls are going to be active.

Midrange Bank

This bank modifies midrange frequencies from 250Hz to 2.5kHz. Knobs are in the middle and run up-and-down

• Knob 4 - "Width or Q":: Controls the size of the bandwidth of the midrange frequencies to be modified.
• Knob 5 - "Boost / Cut": Adjusts the intensity of the midrange with fully clockwise being maximum.
• Knob 6 - "Frequency Select":: Selects the where in the midrange (250Hz to 2.5kHz) that the tone controls are going to be active.

Treble Bank

This bank modifies treble frequencies from 1.1kHz to 11kHz. Knobs are on right side and run up-and-down

• Knob 7 - "Width or Q":Controls the breadth of the treble frequencies to be modified.
• Knob 8 - "Boost / Cut": Adjusts the volume level of the treble frequencies with fully clockwise being fully boosted.
• Knob 9 - "Freq. Select": Adjusts the control of the selected frequency "center" from 1.1kHz to 11kHz.

Master Controls

• Knob 10 - "Master Volume": Adjusts the total volume of the pedal (and all tone controls) with fully clockwise being and addition of more than 30 dB of boost above and beyond the volume boost/cut of each of the frequency band banks.
• Footswitch 1 - "On/Off": This footswitch toggles the pedal between engaged/active ("On"), and bypassed ("Off")

Please note that there is overlap between the frequency shaping of the Bass and Midrange controls (The Midrange bank goes as low as 250Hz, and the Bass bank can go as high as 330Hz), and also with the Midrange and Treble controls (a low of 1.1kHz on the Treble bank, and a high of 2.5kHz on the Midrange bank).

Bypass: True

Like all other BYOC pedals, the Parametric EQ is sold with only true bypass.

General Information

So the Parametric EQ operates like any other parametric equalizer that you might find on the market. We have found not just guitarists, but bass players, keyboard players, and even recording engineers and producers also being attracted to and using parametric equalization. In some cases, a parametric equalizer will be used by a front-of-house sound engineer to isolate a particular frequency when someone's gear is feeding back uncontrollably. When this happens, the offending frequency is reduced to the narrowest possible band, and then cut to kill the feedback loop. The show can then proceed, often with no discernible difference in sound being output by the band - because the single offending frequency was squelched, but that one frequency, in combination with all the others is hard to be picked out by the human ear.

As described above, the BYOC Parametric EQ uses the three same controls across the Bass, Midrange, and Treble frequency ranges. If you don't understand how a parametric equalizer operates these next sections should be of great interest to you.

Width or "Q"

This control is really what allows the parametric equalizer to come into it's own. Once your desired frequency midpoint has been selected, the Q control can be adjusted to expand or contract the range of frequencies modified by the volume control. Please see image on Figure 1

Boost / Cut

Tone controls are functionally no different than volume controls. In fact the exact same electronic component is used for the control: A potentiometer. Where a tone control differs from a volume control is in the filtering that separates out the frequencies to be affected. The resistors and capacitors have been selected specifically for altering the signal tone within a particular range. So when you turn the "Treble" knob on your amplifier up, all you're doing is increasing or decreasing the volume of the treble frequencies that the treble tone control portion of the amplifier circuit is passing through. The same happens on each of the Parametric EQ's "frequency volume" controls.

Freq. Select

This tone control is used to sweep across the range of frequencies available to that particular tone control. In other words, if we're talking about the midrange select control, this control is used to set the central frequency that's being modified by the rest of the controls. Returning to the midrange control, the frequency of the midrange select can vary (depending on the setting) from 250Hz to 2.5kHz

Phase Inversion: Yes/No

Schematic ID	Electronic Part	Action	Phase State
X	X	X	X

Schematic

© Copyright 2019, Thermionic Studios

Artists

We are currently unaware of any artists actively using the pedal now, or who have in the past.

---

Additional Sources