CE-5

Boss CE-5 Chorus Ensemble Pedal. The CE-5 began as a continuation of the same chorus circuit as the Boss CE-2 and CE-3. The General Information section elaborates on how the CE-5 unfolded.

Thermionic Studios owns a CE-5 that is the older, discontinued, analog version. The Boss CE-5 Chorus Ensemble continues to be made, but is only available now as the "new" (post 2001) digital version. Opinions of the digital (post-2001) version of CE-5 tend not to be positive.

Controls

• Knob 1 - "E. Level": (Effect Level) This knob increases the amount of effect (wet) signal as compared to the dry sign
• Knob 2 - "Rate": This knob sets the speed of the modulation of the chorus; clockwise increases the speed.
• Knob 3 - "Depth": This knob sets the depth of the sweep of the chorus; clockwise increases the depth of the sweep.
• Knob 4 - "Filter": This is a dual-knob with an inner- and outer- knob, actually representing two tone controls.
  • Inner Knob - "High": sets the volume of the treble tones, clockwise is more treble.
  • Outer Knob - "Low": sets the volume of the bass tones, clockwise is more bass.
• Footswitch - "On/Off": Switch toggles the pedal on and off
• Output 1 - "Output A: This is the "mono" or wet+dry signal when Output B isn't being used. When Output B is used, Output A is pure wet signal.
• Output 2 - "Output B: This is the "stereo" or "dry only" output jack.

In a pinch it is possible to change the CE-5 from a Chorus pedal to a straight Vibrato pedal by connecting the cord that you're sending to the amplifier into Output A and take a small patch cord and plug it into Output B an then into nothing else. This forces all the wet signal through Output A and the dry signal into Output B. The wet signal is vibrato. When combined (summed) with a non-modulated dry signal, the result is heard by the human ear as a chorus sound. If using this trick be aware that without the effect level at Max, the wet signal will not have unity with the dry signal, causing a volume loss when engaged.

General Information

"CE" Product Line

One of the effects that Boss started their line of pedals with was the CE-1 Chorus Ensemble. This is the old 1970s grey "bean" shaped pedal with two button switches on it. This effect still gets rave reviews on both the lushness and subtlety of the chorus effect. Boss then continued the "CE" designation when they converted to the "classic" 1U stompbox format that we're familiar with today. Their first was the "CE-2 Chorus" which implemented the same circuit, but in a simpler 2-control mono-based effect. Boss then released the "CE-3 Chorus" with the distinctive black knobs with red line indicators (like the Boss VB-2), and stereo outputs. Boss then changed direction and chorus designation and released the "CH-1 Super Chorus".

"CE" then reappeared with the "CE-5 Chorus Ensemble". The earlier CE-5 models share the same pedigree (and MN3007 bucket-brigade delay chip) as the CE-2 and CE-3 and are valued for such. Later models of the CE-5 (labeled CE-5a on the PCB) discard the older analog design and use a new digital architecture. Panasonic stopped producing the MN3007 chip, causing Boss to change to the new digital architecture.

Modifications

It is also possible to modify the analog version of the CE-5 for greater function:

From DIYStompboxes.com:

"Change C22 from 5pF to 22pF (or just solder a 22 pF across C22 on the back of the board). Increasing C22 increases the amount of delay through the bucket-brigade IC (analog delay). Increasing C22 to 22pF has a dramatic and wonderful effect on the depth of the chorus effect."

Pedal Manual

• Boss CE-5 Owner's Manual

Phase Inversion

Our review of the schematic suggests to us that the Boss CE-5 does NOT invert the signal phase. Our explanation is going to be a bit more complicated than that for other pedals...

Output B

We're listing Output B first as it's the easiest to trace (and therefore learn something from).

Electronic Part	Action	Phase State
Q1	Does not Invert	Original
Q2	Does not Invert	Original

For the transistors driving a signal to Output B, we don't read any appearance of inverting electronics, so Output B remains In-Phase.

Output A

Output A is going to be a good bit harder to trace:

Electronic Part	Action	Phase State
Q1	Does not Invert	Original
IC1b	Inverts	Inverted
Q6	Does not Invert	Inverted
Q5	Does not Invert	Inverted
IC2b	Does not Invert	Inverted
IC3a	Inverts	Reverted
IC2a	Inverts	Inverted
IC2b	Inverts	Reverted
IC3b	Does not Invert	Reverted
Q3	Inverts	Inverted
IC1a	Inverts	Reverted (phase back to Original)

Well, this is good. If phase between Output B and Output A were different, that would be a problem! We think this has something to do with the fact that the signal goes through IC2b twice. At least the way we read it, the signal goes through IC2b first for the low frequency filter, and then goes back through IC2b and gets inverted and then goes on to the high frequency filter. Of course, we're electronics novices, so this is speculation on our part; but it also helps us get to where Output A exits the pedal In-Phase...

This is interesting

Notice that there is also signal that gets dumped to the ground of Output B:

Electronic Part	Action	Phase State
Q3	Inverts	Inverted
Q4	Does not Invert	Inverted

Schematic

© Copyright 1991, Roland Corporation.

The schematic was sourced from the Service Manual linked below. The service manual is being made available since the schematic may not be legible enough for everyone interested in viewing it.

• Boss CE-5 Service Manual

Artists

---

Additional Sources