Britannia

The Britannia is a pedal architecture developed by RunoffGroove.com for the purpose of building a sound-alike pedal of the Vox AC-30 with Top Boost amplifier. 1776 Effects developed the printed circuit board(PCB) to match the schematic developed by ROG.

Thermionic Studios has purchased this PCB and sourced the parts necessary to build this pedal. We are in the process of building the pedal and will have more to report upon completion.

Thermionic Studios has one(1) Britannia. When we finish assembling it, it will be available for rental

Controls

Image from Runoff Groove Britannia page
Note Bass & Treble controls are mislabeled.

• Knob 1 - "Brilliance": Sets the amount of treble after the preamp section, increasing treble as control is turned clockwise.
• Knob 2 - "Volume": This knob sets the output level of the pedal with the total volume increasing as the control is turned clockwise.
• Knob 3 - "Treble": Works like an AC/30 amp by boosting treble and upper midrange while cutting bass as the knob is turned clockwise.
• Knob 4 - "Gain": Sets the amount of overdrive in the preamp section, increasing the gain as the knob is turned clockwise.
• Knob 5 - "Bass": Sets the amount of bass frequencies in the signal with most bass available when control is fully clockwise.
• Footswitch 1 - "On/Off": This switch toggles the effect between "off" (bypass) and "on" (active).

Bypass: True

The Brittania is a true bypass pedal.

General Information

http://1776effects.com/wp-content/uploads/2015/03/Britannia-BOM.pdf

The Britannia can be powered by a 9-volt battery, or a tip-negative Boss-style 9-volt power adapter. The transistors must be biased correctly for this pedal, sound-wise, to sound as accurate as possible to an actual Vox AC/30 amplifier.

Pedal Manual

As of this time, 1776 Effects has not issued a separate manual on how to use the pedal. The best references are either this wiki page, the entry on the Runoff Groove website, or the build manual from 1776 Effects which describes the architecture of the pedal.

Runoff Groove offers the following advice when attempting to use the Britannia with a treble booster:

If you would like to use a treble booster at the input of Britannia like Brian May did into the AC-30 Normal channel, we recommend that you start with the following configuration: set the Bass control at maximum, the Treble control at minimum, and the Brilliance control at noon; adjust the Gain control as desired, and then fine-tune the sound to your liking with the Bass, Treble and Brilliance controls. Use of a flat or full frequency booster in front of Britannia will also produce some interesting sounds.

Build Details

In the instance where this is a pedal built by Thermionic Studios, provide the specifics of the build in this section here. In the instance of a production pedal, either post an image of the completed PCB of the production in the enclosure, or remove this page section entirely.

JMKPCBs Testing Rig PCB

Item	Value
PCB Creator	(PCB Creator)
PCB Dimensions	length X width (metric) length x width (SAE)
Enclosure Size	Hammond 1590(!!)/1550(!!)
Enclosure Orientation	Portrait / Landscape
Power Adapter	9 volts, Standard Boss "barrel-negative" supply 9-volt battery snap available
Power Consumption	'XXX' milliamps

Phase Inversion: Yes

From our examination of the schematic below, the Britannia appears to invert phase on the output as compared with the signal that goes into the pedal.

Schematic ID	Electronic Part	Action	Phase State
Q1	2N5457	Inverts	Inverted
Q2	J201	Inverts	Reverted
Q3	2N5088	Does not Invert	Reverted
Q4	J201	Inverts	Inverted
IC1a	TL072	Does not Invert	Inverted
IC1b	TL072	Does not Invert	Inverted

This will need to be borne out by testing and observation.

Schematic

© Copyright 2013, runoffgroove.com

Artists

We are currently unaware of any artists actively using the pedal now, or who have in the past.

---

Additional Sources

1. http://www.runoffgroove.com/britannia.html